arrow-firmware/main/cc1200.c

/*
 * Project: Arrow
 * Author: 	curiousmuch
 */
#include <stdio.h>
#include <math.h>
#include "freertos/FreeRTOS.h"
#include "freertos/task.h"
#include "driver/gpio.h"
#include "sdkconfig.h"
#include "driver/spi_master.h"
#include "esp_err.h"
#include "cc1200.h"
#include "cc1200_protocol.h"
#include "board.h"
#include "esp_task_wdt.h"
#include "freertos/ringbuf.h"

#define CC1200_WRITE_BIT 	0
#define CC1200_READ_BIT 	BIT(1)
#define CC1200_BURST_BIT 	BIT(0)

// Public Configurations for CC1120 SPI Driver
spi_bus_config_t bus_config =
{
	.miso_io_num = CC1120_MISO,
	.mosi_io_num = CC1120_MOSI,
	.sclk_io_num = CC1120_SCLK,
	.quadwp_io_num = -1,
	.quadhd_io_num = -1,
	.max_transfer_sz = 150,
	.flags = ESP_INTR_FLAG_IRAM
};


spi_device_interface_config_t interface_config =
{
	.command_bits = 2,
	.address_bits = 6,
	.dummy_bits = 0,
	.mode = 0,
	.spics_io_num = CC1120_CS,
	.clock_speed_hz = (APB_CLK_FREQ/20),
	.flags = 0,
	.queue_size = 20

};

spi_device_handle_t spi;

// Private CC1120 Driver Functions
void cc1200_gpio_init(void)
{
	gpio_config_t reset_pin_config =
	{
			.pin_bit_mask = (uint64_t)(BIT64(CC1120_RESET)),
			.mode = GPIO_MODE_OUTPUT,
			.pull_up_en = GPIO_PULLUP_DISABLE,
			.pull_down_en = GPIO_PULLDOWN_DISABLE,
			.intr_type = GPIO_INTR_DISABLE

	};
	gpio_config_t gpio_pin_config =
	{
			.pin_bit_mask = (uint64_t) (BIT64(CC1120_GPIO0)|BIT64(CC1120_GPIO2)|BIT64(CC1120_GPIO3)),
			.mode = GPIO_MODE_INPUT,
			.pull_up_en = GPIO_PULLUP_DISABLE,
			.pull_down_en = GPIO_PULLDOWN_DISABLE,
			.intr_type = GPIO_INTR_DISABLE
	};
	gpio_config_t debug_pin_config =
	{
			.pin_bit_mask = (uint64_t) (BIT64(DEBUG_0)|BIT64(DEBUG_1)),
			.mode = GPIO_MODE_OUTPUT,
			.pull_up_en = GPIO_PULLUP_DISABLE,
			.pull_down_en = GPIO_PULLDOWN_DISABLE,
			.intr_type = GPIO_INTR_DISABLE
	};

	gpio_config(&reset_pin_config);
	gpio_config(&gpio_pin_config);
	gpio_config(&debug_pin_config);


	gpio_set_level(CC1120_RESET, 1);

}

void cc1200_spi_init(void)
{
	esp_err_t ret;
	ret = spi_bus_initialize(VSPI_HOST, &bus_config, 0);	// this uses DMA channel 1
	ESP_ERROR_CHECK(ret);
	ret = spi_bus_add_device(VSPI_HOST, &interface_config, &spi);
	ESP_ERROR_CHECK(ret);
}

void IRAM_ATTR cc1200_spi_write_byte(uint16_t addr, uint8_t data)
{
	esp_err_t ret;
	spi_transaction_t tx_trans =
	{
		.flags = SPI_TRANS_USE_TXDATA,
		.cmd = CC1200_WRITE_BIT,
		.addr = addr,
		.length = 8,
		.rxlength = 0,
		.tx_data[0] = data

	};

	if ((addr & 0xFF00) != 0) // send data with extended address in command field
	{
		tx_trans.flags |= (SPI_TRANS_VARIABLE_CMD | SPI_TRANS_VARIABLE_ADDR);
		spi_transaction_ext_t tx_trans_ext =
		{
				.base = tx_trans,
				.command_bits = 2,
				.address_bits = 14
		};
		ret = spi_device_polling_transmit(spi, (spi_transaction_t*)&tx_trans_ext);
	}
	else
	{
		ret = spi_device_polling_transmit(spi, &tx_trans);
	}
	ESP_ERROR_CHECK(ret);
}

void IRAM_ATTR cc1200_spi_write_bytes(uint16_t addr, uint8_t* data, uint8_t len)
{
	esp_err_t ret;
	spi_transaction_t tx_trans =
	{
		.cmd = (CC1200_WRITE_BIT | CC1200_BURST_BIT),
		.addr = addr,
		.length = 8*len,
		.tx_buffer = data
	};
	if ((addr & 0xFF00) != 0) // send data with extended address in command field
	{
		tx_trans.flags |= (SPI_TRANS_VARIABLE_CMD | SPI_TRANS_VARIABLE_ADDR);
		spi_transaction_ext_t tx_trans_ext =
		{
				.base = tx_trans,
				.command_bits = 2,
				.address_bits = 14
		};
		ret = spi_device_polling_transmit(spi, (spi_transaction_t*)&tx_trans_ext);
	}
	else
	{
		ret = spi_device_polling_transmit(spi, &tx_trans);
	}
	ESP_ERROR_CHECK(ret);
}

void IRAM_ATTR cc1200_spi_read_byte(uint16_t addr, uint8_t* data)
{
	esp_err_t ret;
	spi_transaction_t rx_trans =
	{
		.cmd = CC1200_READ_BIT,
		.addr = addr,
		.length = 8,
		.rxlength = 8,
		.rx_buffer = data
	};
	if ((addr & 0xFF00) != 0) // read data with extended address in command field
	{
		rx_trans.flags |= (SPI_TRANS_VARIABLE_CMD | SPI_TRANS_VARIABLE_ADDR);
		spi_transaction_ext_t rx_trans_ext =
		{
				.base = rx_trans,
				.command_bits = 2,
				.address_bits = 14
		};
		ret = spi_device_polling_transmit(spi, (spi_transaction_t*)&rx_trans_ext);
	}
	else
	{
		ret = spi_device_polling_transmit(spi, &rx_trans);
	}
	ESP_ERROR_CHECK(ret);
}

void cc1200_spi_read_bytes(uint16_t addr, uint8_t* data, uint8_t len)
{
	esp_err_t ret;
	spi_transaction_t rx_trans =
	{
		.cmd = (CC1200_READ_BIT | CC1200_BURST_BIT),
		.addr = addr,
		.length = 8*len,
		.rxlength = 8*len,
		.rx_buffer = data
	};
	if ((addr & 0xFF00) != 0) // read data with extended address in command field
	{
		rx_trans.flags |= (SPI_TRANS_VARIABLE_CMD | SPI_TRANS_VARIABLE_ADDR);
		spi_transaction_ext_t rx_trans_ext =
		{
				.base = rx_trans,
				.command_bits = 2,
				.address_bits = 14
		};
		ret = spi_device_polling_transmit(spi, (spi_transaction_t*)&rx_trans_ext);
	}
	else
	{
		ret = spi_device_polling_transmit(spi, &rx_trans);
	}
	ESP_ERROR_CHECK(ret);
}

rf_status_t IRAM_ATTR cc1200_spi_strobe(uint8_t cmd)
{
	esp_err_t ret;
	uint8_t temp=0;
	spi_transaction_t rx_trans =
	{
		.flags = (SPI_TRANS_USE_TXDATA | SPI_TRANS_VARIABLE_CMD | SPI_TRANS_VARIABLE_ADDR),
		.length = 8,
		.rxlength = 8,
		.rx_buffer = &temp,
		.tx_data[0] = cmd
	};
	spi_transaction_ext_t rx_trans_ext =
	{
			.base = rx_trans,
			.command_bits = 0,
			.address_bits = 0
	};
	ret = spi_device_transmit(spi, (spi_transaction_t*)&rx_trans_ext);
	ESP_ERROR_CHECK(ret);
	return (temp & 0xF0);
}

// Public CC1120 Driver Functions
// These function should have there own error codes as they're dependent upon the radio and
// not the ESP32 :)

rf_status_t cc1200_radio_reset(void)
{
	rf_status_t status;
	uint8_t retry_count = 0;
	cc1200_spi_strobe(CC120X_SRES);
	status = cc1200_spi_strobe(CC120X_SNOP);

	vTaskDelay(10 / portTICK_PERIOD_MS);

	while((CC120X_RDYn_BIT & (status & 0x80)))
	{
		vTaskDelay(10 / portTICK_PERIOD_MS);
		if (retry_count > 3)
		{
			// place error CC1120 timeout
			printf("CC1120 Reset Failure\n");
			break;
		}
		status = cc1200_spi_strobe(CC120X_SNOP);
		retry_count++;
	}
	printf("%x\n", retry_count);
	return status;
}

// f_RF = f_VCO / LO Divider
#define CC1200_LO_DIVIDER	24 			// 136.7 - 160 MHz Band
#define CC1200_XOSC 		40000000	// 40MHz
// f_VCO = FREQ / 2^16 * f_XOSX + FREQOFF / 2^18 * F_XOSC

esp_err_t cc1200_radio_frequency(uint32_t freq)
{
	// calculate FREQ0, FREQ, FREQ2 registers
	volatile double temp_freq;
	temp_freq = ((double) freq * 65536 * CC1200_LO_DIVIDER) / CC1200_XOSC;
	freq = (uint32_t)temp_freq;
	cc1200_spi_write_byte(CC120X_FREQ0, ((uint8_t *)&freq)[0]);
	cc1200_spi_write_byte(CC120X_FREQ1, ((uint8_t *)&freq)[1]);
	cc1200_spi_write_byte(CC120X_FREQ2, ((uint8_t *)&freq)[2]);
	return ESP_OK;
}

esp_err_t cc1200_radio_sleep(void)
{
	return ESP_OK;
}

esp_err_t cc1200_radio_power(uint8_t txPower)
{
	return ESP_OK;
}


#define HDLC_FLAG 0x7E
#define HDLC_FLAG_LEN 10

uint8_t packet_len = 0;
uint8_t test_vector[] = {0x71, 0x01, 023, 0xAE, 0x75};
volatile uint8_t sample_count = 0;
uint8_t toggle;
uint8_t toggle2;
uint8_t prev_sample_count = 0;
uint32_t tx_symbol = 0;
uint8_t prev_tx_symbol = 0;



#define SAMPLE_FREQUENCY 13200
#define DAC_MAX 64
#define LUT_SIZE 128

DRAM_ATTR int8_t LUT[LUT_SIZE];

int32_t phase_i = 0;
volatile uint8_t new_sample = 0;

float phase = 0.0f;
float delta_phi = 0.0f;
float const delta_phi_1 = (float) 1200 / SAMPLE_FREQUENCY * LUT_SIZE;
float const delta_phi_2 = (float) 2200 / SAMPLE_FREQUENCY * LUT_SIZE;
uint8_t data;


// The output needs to be continous phase.

typedef struct {
	uint8_t one_count;
	uint32_t sample_count;
	uint32_t byte;
	uint32_t packet_len;
	uint8_t prev_bit;
	uint8_t cur_bit;
	uint8_t tone;
} aprs_flags_t;

aprs_flags_t DRAM_ATTR aprs_flags = {
		.one_count = 0,
		.sample_count = 0,
		.byte = 0,
//		.packet_len = sizeof(APRS_TEST_PACKET)/sizeof(uint8_t),
		.prev_bit = 0,
		.cur_bit = 0,
		.tone = 0
};

static void IRAM_ATTR LUT_lookup(void)
{
	if (aprs_flags.tone)
		delta_phi = delta_phi_1;
	else
		delta_phi = delta_phi_2;

    phase_i = (int32_t)phase;        // get integer part of our phase

    phase += delta_phi;              // increment phase

    if (phase >= (float)LUT_SIZE)    // handle wraparound
        phase -= (float)LUT_SIZE;
}

static void IRAM_ATTR cc1200_aprs_tx_isr(void* arg)
{
    cc1200_spi_write_byte(CC120X_CFM_TX_DATA_IN, LUT[phase_i]);

    sample_count++;
    new_sample = 1;

	toggle = toggle ^ 1;
	gpio_set_level(DEBUG_1, toggle);
}

void cc1200_lut_init(void)
{
	int16_t i=0;
	for (i=0; i<LUT_SIZE; ++i)
	{
		LUT[i] = (int8_t)roundf(DAC_MAX * sinf(2.0f * M_PI * (float)i / LUT_SIZE));
		//printf("%d,\n", LUT[i]);
	}
}

#define PREAMBLE_LENGTH 20
#define SUFFIX_LENGTH 1

void IRAM_ATTR cc1200_radio_APRSTXPacket(uint8_t  *f, uint16_t f_len, uint8_t tx_delay, uint8_t tx_tail)
{
	// start CW transmission
	cc1200_spi_write_byte(CC120X_FIFO, 0x12);
	cc1200_spi_strobe(CC120X_STX);

	// enable interrupt pin for CC1120 for timing packets
	gpio_install_isr_service(ESP_INTR_FLAG_IRAM);

	gpio_isr_handler_add(CC1120_GPIO3, cc1200_aprs_tx_isr, NULL);
	gpio_set_intr_type(CC1120_GPIO3, GPIO_INTR_POSEDGE);

	// acquire SPI bus for fastest possible SPI transactions
	spi_device_acquire_bus(spi, portMAX_DELAY);


	int16_t i,j;
	uint16_t p_len = tx_delay * 12;
	uint16_t t_len = tx_tail * 12;

		// Start CW transmission
		cc1200_spi_write_byte(CC120X_FIFO, 0x12);
		cc1200_spi_strobe(CC120X_STX);

		sample_count = 0;
		new_sample = 0;

		// Send HDLC Flag for TX Delay Time
		for (i = 0; i<p_len; i++)
		{
			aprs_flags.byte = 0x7E;
			for(j=0; j<8; j++)
			{
				aprs_flags.cur_bit = aprs_flags.byte & 0x01;

				// NRZ-I Encoding
				if (aprs_flags.cur_bit)
				{
					// do nothing
					aprs_flags.one_count++;

				}
				else
				{
					aprs_flags.tone = aprs_flags.tone ^ 1; // switch tone
					aprs_flags.one_count = 0;
				}

				aprs_flags.byte = (aprs_flags.byte >> 1);

				while(sample_count < 11)	// wait for symbol to be sent
				{
					if ( new_sample )
					{
						LUT_lookup();
						new_sample = 0;
					}
				}
				sample_count = 0;
				//printf("Symbol: %x\n", aprs_flags.cur_bit);

			}
		}
		aprs_flags.one_count = 0;

		// Send Packet / Frame
		//for (i=0;i<aprs_flags.packet_len;i++)
		for (i=0;i<f_len;i++)
		{
			aprs_flags.byte = f[i];
			for(j=0; j<8; j++)
			{
				aprs_flags.cur_bit = aprs_flags.byte & 0x01;	// bool of first bit

				// Zero Stuffing
				if (aprs_flags.one_count == 5)
				{
					aprs_flags.tone = aprs_flags.tone ^ 1;
					aprs_flags.one_count = 0;

					// wait for symbol to be sent
					while(sample_count < 11)
					{
						if ( new_sample )
						{
							LUT_lookup();
							new_sample = 0;
						}
					}
					toggle2 = toggle2 ^ 1;
					gpio_set_level(DEBUG_0, toggle2);
					sample_count = 0;
				}

				// NRZ-I Encoding
				if (aprs_flags.cur_bit)
				{
					// do nothing
					aprs_flags.one_count++;

				}
				else
				{
					aprs_flags.tone = aprs_flags.tone ^ 1; // switch tone
					aprs_flags.one_count = 0;
				}

				aprs_flags.byte = (aprs_flags.byte >> 1);

				while(sample_count < 11)	// wait for symbol to be sent
				{
					if ( new_sample )
					{
						LUT_lookup();
						new_sample = 0;
					}
				}
				toggle2 = toggle2 ^ 1;
				gpio_set_level(DEBUG_0, toggle2);
				sample_count = 0;
				//printf("Symbol: %x\n", aprs_flags.cur_bit);
			}
		}
		aprs_flags.one_count = 0;

		// Send HDLC Flag for TX Tail
		for (i = 0; i<t_len; i++)
		{
			aprs_flags.byte = 0x7E;
			for(j=0; j<8;j++)
			{
				aprs_flags.cur_bit = aprs_flags.byte & 0x01;

				// NRZ-I Encoding
				if (aprs_flags.cur_bit)
				{
					// do nothing
					aprs_flags.one_count++;

				}
				else
				{
					aprs_flags.tone = aprs_flags.tone ^ 1; // switch tone
					aprs_flags.one_count = 0;
				}

				aprs_flags.byte = (aprs_flags.byte >> 1);

				while(sample_count < 11)	// wait for symbol to be sent
				{
					if ( new_sample )
					{
						LUT_lookup();
						new_sample = 0;
					}
				}
				sample_count = 0;

			}
		}
		cc1200_spi_strobe(CC120X_SIDLE);
}

RingbufHandle_t cfm_buf_handle;

static void IRAM_ATTR cc1200_aprs_rx_isr(void* arg)
{
	//uint8_t data = 0;

	cc1200_spi_read_byte(CC120X_CFM_RX_DATA_OUT, &data);

	toggle = toggle ^ 1;
	gpio_set_level(DEBUG_1, toggle);
	xRingbufferSendFromISR(cfm_buf_handle, &data, sizeof(data), NULL);
	//ets_write_char_uart(data);
    //new_sample = 1;

}

void IRAM_ATTR cc1200_radio_APRSRXPacket(void)
{
	printf("Starting Continuous RX\n");
	// start RX transmission
	//cc1120_spi_write_byte(CC112X_FIFO, 0x12);
	cc1200_spi_strobe(CC120X_SRX);
	vTaskDelay(20/portTICK_PERIOD_MS);
	cc1200_spi_strobe(CC120X_SRX);

	// acquire SPI bus for fastest possible SPI transactions
	spi_device_acquire_bus(spi, portMAX_DELAY);

	// enable interrupt pin for CC1120 for timing packets
	gpio_install_isr_service(ESP_INTR_FLAG_IRAM);

	gpio_isr_handler_add(CC1120_GPIO3, cc1200_aprs_rx_isr, NULL);
	gpio_set_intr_type(CC1120_GPIO3, GPIO_INTR_POSEDGE);

}

void cc1200_radio_init(const cc1200_reg_settings_t* rf_settings, uint8_t len)
{
	cc1200_gpio_init();
	cc1200_spi_init();
	cc1200_lut_init();

	cc1200_radio_reset();	gpio_set_level(CC1120_RESET, 1);

	uint8_t data;
	cc1200_spi_read_byte(CC120X_PARTNUMBER, &data);
	printf("%x", data);


	uint8_t i;

	for (i=0;i<len;i++)
	{
		cc1200_spi_write_byte(rf_settings[i].addr, rf_settings[i].data);
	}
}